Vince’s Upholstery – Reupholster

By Frank Parker

We had previously reupholstered a Parker-Knoll 60’s wing back chair for a client who then requested us to reupholster two 2 ½ seater settees purchased in the early 80’s made by Vince’s Upholstery.

Vince’s Upholstery was founded by Vince and Pina Scalisi who originally started the business from their home in East Perth making budget priced furniture. They progressed over time and became renowned for manufacturing top end custom-made lounge furniture from a purpose built factory in Morley.

Our clients presented us with two identical looking 2 ½ seater settees however when we removed the fabric it became obvious they were purchased at different times as one settee featured a traditional sprung edge and the other a fabricated foam edge with different springs. The challenge was to reupholster the two settees so they both felt identical for comfort.

We re-webbed the seats and fitted new coil springs of the same height and gauge then fabricated a foam edge on one settee to replicate the sprung edge of the other. We also replaced all existing hessian and body padding however the down and feather cushion inners were still in good condition so we encased these in 200g boned polyester fibre. The settees were reupholstered to the original finish in a cotton velvet then delivered to very happy clients!

Call us Today

Similar Posts

  • Restoration of Club Lounge

    ByFrank Parker
    Reupholster Club Lounge Perth

    What we generally recognise as Australian styled ‘club lounges’ were made from the late 1920’s through to the mid 1950’s. This design was not uniquely Australian however it was very popular in Australia during this era and the suite featured is typical of this period however many variations were available.

    These lounge suites all featured the wide arms, usually with timber trays and bases but some also had decorative timber trim on the arm facings. The upholstery finishes were also available in a wide variation of finishes. This included cord trim, contrast piping and raised panel patterns on the inside backs.

    A client approached us who is from a prominent furniture manufacturing family to restore their ‘club lounge’. This club lounge was not a family heirloom but a design from the era they had always found interesting and destined for their retirement home. It is always an honour to be asked by a contemporary to restore a favourite piece of furniture however the expectations are always as equally high.

    We stripped the 3 seater and 2 chairs down to the bare frames, removed the show-wood components then screwed the joints together. The timber arm trays were so badly damaged leaving us with no option than to completely replace them however the front base strips were sanded back and re-used have receiver three coats of lacquer.

    The bases and backs were re-webbed with jute webbing then the coil springs laced in, tied down and covered with heavy weight hessian. We then used synthetic ‘thumb roll’ to build up the edges and laminated layers of premium foam over the bases, arms and inside backs until the desired shapes were achieved. Flutes were sewn into the inside back covers and the suite was trimmed with contrast piping. The seat cushion inserts were fabricated by laminating various densities of premium foam then encasing them with bonded polyester fibre. The outside arms and outside backs were all lined padded providing a superior finish.

    The result was that we had brought furniture made about 80 years ago back to life. We trust the new owners will receive many years of enjoyable use of their furniture. However from a trade persons perspective we often wonder, what would those who originally made the furniture think of it now?

    Call us Today

  • Reupholster Parker Furniture

    ByFrank Parker

    Parker Furniture commenced operations in 1935 as Dagger & Parker formed by Alf Dagger and Jack Parker making chairs and cabinets fashioned from packing palettes. Post war they manufactured reproduction Queen Anne and Art Deco designs then Alf Dagger resigned and the business was renamed JW Parker and then Parker Furniture.

    Tony Parker joined the business in 1949 working in the polishing and finishing area while studying furniture design at East Sydney Technical College at night. Tony then left the business for the UK working in furniture sales management and design for John Lewis. Jack reluctantly made some of Tony’s modernist UK inspired designs but showed little commitment in promoting these designs. Tony then displayed these new designs at the Sydney Furniture Exhibition with a year’s production being sold in four days! Grace Bros. then stocked and displayed these new designs with sales expanding so did the staff and the factories. After several shifts Parker Furniture premises was situated on eight hectares at Seven Hills and the business employed over 380 staff by 1973.  

    The brothers sold the family business in 1990’s but without their enthusiasm and due to a changing market the company had closed by 1997. Covermore Designs rose from the ashes formed by former Parker employees and is still going strong today manufacturing some classic company designs and re-furbishing past production pieces.

    A client approached wanting her Parker lounge suite to be re-upholstered. They had previously lived in Sydney and had purchased this suite in the early 1980’s. The lounge suite remained in exceptional condition, partially due to care but also testament to the quality design and construction.

    Our client selected a linen similar to her original choice for the re-upholstery. We removed the existing upholstery with the timber frame and springing system still in superb condition. New premium padding was laminated onto the arms and frame body. New polyester encased premium seat cushions were fabricated also polyester filled channelled and quilted back cushion inners were made. The lounge suite was then re-upholstered being carefully pattern matched at all stages.

    Our client was overwhelmed with her re-upholstered Parker lounge suite as it was delivered into her home it took her back to a bygone time.

    Call us Today

  • Cornwell Norton chairs – Reupholster

    ByFrank Parker

    Cornwell Furniture was formed in the 1960’s, a division of Parker Knoll Furniture in the United Kingdom. Cornwell was a signature range of Parker-Knoll specialising in high quality mass production motion chairs.

    The chair pictured is branded “Cornwell-Norton Ltd” which signifies it was manufactured in the Cornwell factory located at Chipping Norton in West Oxfordshire which commenced operations in the mid 60’s and closed in 2003.

    Our clients having migrated from the UK in the 1970’s had by now only a few remnant pieces of furniture from the homeland but their pride piece was this Cornwell Norton motion chair which they wanted rejuvenated..

    We completely removed all the upholstery from the frame which was well constructed from Beech and plywood. The mechanical action was a simple push mechanism however it remained in good working condition which is a tribute to the designers of the day. The frame required no attention and was re-webbed using heavy grade elastic webbing then padded utilising high density polyurethane foam. The cushion inserts were fabricated from premium foam and encased with bonded polyester fibre and the outside arms and outside back were lined then padded.

    The fabric selected by our clients was an English striped chenille which was period for the furniture and also suited the particular design. The chair was then upholstered to its original condition trimmed with piping and the cushions completed with buttoning.

    Our clients were elated with their chair rejuvenated to back to its stylish sixties finish and no doubt it bought back many wonderful memories of the era.

    Call us Today

  • Oliver’s Upholstery

    ByFrank Parker

    Oliver’s Upholstery was founded by Andrew Oliver in the late 1980’s being situated in Perth Western Australia. The business manufactured economically priced upholstered furniture for the WA retail sector. The business grew quickly becoming one of the larger upholstery manufacturers by volume in the State. However about a decade of operation cheap inferior products started coming into Australia from Malaysia and Thailand then flooding in from China.

    With the value area of the local market being displaced with imported furniture Andrew Oliver changed directions renaming the business Oliver’s Re-upholstery focusing on re-upholstery and commercial upholstery.

    Long term clients approached us when renovating their home wanting to have two wing back chairs re-upholstered. These clients resided in a leafy Perth suburb and thought the chairs were rather special but it’s difficult to explain to such clients that their taste in furniture maybe a bit ordinary, especially if they want the chairs re-upholstered in a high quality leather.

    The upholstery was rather tacky so we stripped the chairs back to the bare frames and were rather surprised that the frames were soundly constructed. We sprung the frames, laminated the body work with high density foam padding slightly redesigning the upholstery. The leather was a full-aniline leather from Tasman Tanning and was a pleasure to use as the chairs took shape. Using more traditional labour intensive upholstery techniques paid off as displayed by the finished product.

    Our clients were simply “gob-smacked” with their re-upholstered wing back chairs which just goes to show that you can make a silk purse from a sow’s ear!

    Call us Today

  • Reupholstery of Jarvi Furniture Lounge

    ByFrank Parker

    A Special Wedding Gift

    A couple were getting married and had requested of their wedding guests to contribute to the re-upholstery of their ‘Jarvi’ lounge suite. This lounge furniture with a matching table and cabinetry was purchased by the Groom in NSW some time ago and the fabric for the re-upholstery selected by the Bride.

    The History of Jarvi Furniture

    Jarvi Furniture was founded by Len Jarvi, who was born in Finland in 1910. Len migrated to Australia learning his trade at Chesterfield Furniture in Botany NSW. He then established Jarvi Furniture in Sydney after the war. They were focused on manufacturing high quality lounge and dining furniture influenced on the Jacobean style of furniture. Len Jarvi died in an accident on his farm in 1959 however his quality furniture still lives on today.

    The Lounge Suite Restoration Process

    We worked on restoring the frame of the lounge through the following process:

    • Stripped this lounge suite down to the bare frame
    • Repaired several minor structural defects
    • cleaned and polished the show-wood frame
    • re-webbed the bases with jute webbing
    • coil springs were laced into place and then overlayed with hessian
    • Several modern materials were used to finish of the sprung edge (whilst maintaining quality)
    • Placed a synthetic thumb-roll on the front edge and
    • Then finished with a high density foam overlay

    Finally, the front edge and borders were hand sewn to give the traditional finish.

    The Final Part of the Lounge Reupholstery

    The seat and back cushions were box piped using cotton piping cord. We also incorporated zip borders so the cushions are removable. The cushion inserts we used were laminated premium quality polyurethane foams encased in bonded polyester fibre. The result being firm resilient cushioning that will last for decades.

    Such a special gift for this newly married couple.

    Call us Today to Get Your Furniture Reupholstered

  • Re-upholster leather Tessa furniture

    ByFrank Parker

    Tessa Furniture is an iconic name in Australian furniture manufacturing being a prolific name during the heydays of local furniture industry. Although refurbished mid-century modernist furniture with a Scandinavian influence is a niche market the interest not only resides with those who have been fortunate to have witnessed this period of design history. Some discerning members of younger generations are purchasing or inheriting this furniture and having it restored.  

    A client approached us with her much loved Tessa leather lounge suite which she had inherited from her parents. She wanted the lounge fully restored as she remembered it growing up on the family farm.

    We completely removed all existing upholstery then sanded the frame back to bare timber. Several timber rails were re-glued then the frame was finely sanded. The Tasmanian Myrtle timber frame was then stained back to the original finish and given three coats of lacquer being lightly sanded between coats.

    The original springing systems were fine in the backs and the settee seat however new premium quality elastic webbing was fitted to the chair seats to conform to the original specifications. New channelled and quilted polyester back cushion inners were fabricated likewise new polyester encased premium polyurethane seat cushion inners. The quality of the seat and back cushion inners however far exceeded the original upholstery componentry.

    It is extremely important to use a high quality leather for the upholstery and we used the Tasman ‘Matisse Manuka’ which is a superior quality semi-aniline leather from New Zealand. All the detailed stitching was replicated and needless to say that our client was elated at the family lounge suite being returned to its former glory days.

    Call us Today