Co-ordinating classic chairs

By Frank Parker

Timberline Furniture commenced operations in Perth WA with the factory being located in Willetton. The furniture manufacturing business was founded by Ron Jones and Hedley Van Der Straaten in the early 70’s and ran through to the mid 90’s with about 10 – 12 staff. Ron was a Wood-Turner by trade and managed operations with Hedley managing sales and general business. Timberline predominantly manufactured dining furniture but also made some lounge and occasional furniture. During the 80’s they entered into a collaborative venture with co-ordinated designs, Trustyle Furniture making the lounge suites, George’s Cabinets making the cabinetry and Timberline the dining suites. These co-ordinated furniture ranges were sold by furniture retailers throughout W.A.     

Our clients were involved in furniture retailing and furniture transport for many decades and contacted us to re-upholster their Timberline ‘Captain’s Chairs’. These were a very popular occasional chair from the late 70’s and early 80’s not just in residential sales but they were also used in commercial hospitality applications.

The chairs were originally upholstered in a Nylex Deerhide’ vinyl which was a quality product in its days so we advised using a vinyl from the Austex ‘Studio’ as a quality replacement. The existing upholstery was completely removed, then the show-wood frames cleaned and polished. New high density foam was laminated onto the padded areas and the chairs were upholstered to the original finish with piped and space studded detail.

Our clients re-upholstered ‘Captain’s Chairs’ looked in place around their bar with complimentary comments passed over a few drinks.

Similar Posts

  • Reupholster Art Deco Chairs

    From our understanding these chairs were made in Czechoslovakia in the late 1920’s, manufacturer unknown. For their time the construction techniques used are quite advanced utilising a ‘push-in seat’ and back flutes located with spring-edge wire. However the most significant thing about these chairs is the general proportion and balance of the design.

    A client contacted us saying that she had acquired two art deco European chairs requiring restoration. Upon initial inspection we found the chairs had been shabbily re-upholstered and covered in decades of grime. As we stripped away the fabric on these chairs it exposed some of the original upholstery providing enough information for an authentic reconstruction.

    The first step was several construction repairs to the timber frames then removing the layers of grime. The show-wood components of the frames were then gently sanded back, stained a mid-tone Oak then three coats of clear lacquer. Then with the upholstery we re-constructed the sprung edge seats and backs by lacing in the springs, fabricated the spring edge wire and tying down the springs. We then sewed on the hessian overlays and ring-clipped on polyurethane edge moulding. The seats and backs were then layered with premium foam and polyester overlays. The client’s fabric selection suited the chairs and was practical to upholster. The panels were cut being carefully pattern matched then largely pre-sewn but requiring some hand stitching.

    The re-furbishing of these chairs combined traditional methods with modern materials however did not compromise the design integrity. Our client was overjoyed with the result and the chairs now take pride of place in her lounge room.

    Call us Today
  • Trustyle Furniture

    Truestyle evolved from a lounge furniture manufacturing business which came into existence as W. E. Young & Co. The business was founded by Bill and Beryl Young who came to WA from Victoria starting the manufacturing business in the late 1950’s originally located in Claverton Street east Perth. In the late 1960’s the business relocated to Osborne Park.  The business was then taken over by several of the employees in the mid 1970’s with Colin Bainbridge running operations. The business then shifted to River road Bayswater to a purpose built factory.

    Trustyle manufactured styles incorporating show-wood frames with the furniture being in the upper middle class for price and quality always being considered good value for money in the industry.

    A client contacted us wishing to have her Trustyle lounge suite and dining chair seats re-upholstered. The Lounge suite was over thirty years old but remained structurally sound. It was originally upholstered in a patterned transfer print which were popular in the late 80’s and early 90’s but she decided to have the furniture re-upholstered in a plain chenille.

    This was a straight forward job, we replaced the elastic webbing laminated new high density arm foam and fabricated new premium foam seat and back cushions encasing them with bonded polyester fibre. The upholstery was also relatively simple and back to original including the buttoning.

    Our client was happy as her favourite piece of furniture was back to new condition and hopefully she will have many years of enjoyable use.

    Call us Today
  • Mechanical rocker/glider chair – reupholster

    Mechanical rocker/glider chairs or platform rocker chairs are a type of rocking chair which moves as a swing seat, where the entire frame of the seat is attached to the base by means of a double rocker four bar linkage. The non-parallel suspension arms of the linkage cause the chair to simulate the motion of a rocking chair. The mechanical rocker/glider chairs were first manufactured in the United States and Canada during the 1930’s.

    Our client in her late 80’s approached us to rejuvenate her rocker glider chair and we just loved her story. As a young child in the pre-war years she travelled from her home in Rugby England with her father by train to Edinburgh Scotland to visit her grandmother. Apparently her grandmother had very strict house rules however when she had the chance she would love to rock in her grandmother’s chair. A few years later after the passing of her grandmother her aunty asked if she would like any of her grandmother’s possessions with the obvious response, “the rocking chair”. Then some eighty years later we were given the task of reupholstering her special chair.

    Our client had selected an olive cut pile cotton velvet for the upholstery which suited the chair and reflected the era. All the upholstery was removed from the chair then the timber frame was cleaned and polished. Jute webbing was fitted over the seat and then a hessian overlay and premium padding with a polyester overlay. After the outside back was fitted the same process as the seat occurred then the arms pads were built up with premium padding and polyester overlays. The inside back, seat and arm pads were then upholstered and unlike the original chair which was trimmed with gimp we used self-covered banding which was then space studded.

    When the chair was delivered our client had tears of joy saying this was something she had wanted to do all her life.

    Call us Today
  • Restoration of Antique Chairs

    Genuine fine antique chairs become scarcer as time ticks on due to fatigue with function and unnecessary destruction. Poor and inappropriate furniture repairs due to operators not possessing the necessary skills also increase the scarcity. It is important to always use a reputable and skilled restorer.

    Our client approached us with a dining chair from the 1880’s which was bequeathed to her by her maternal grandmother as one was for each granddaughter. After receiving the chair she had it repaired and re-upholstered however within a short time with only gentle use the lower back carved section again broke away. The chair remained in her lounge room as a decorative piece for several decades but constantly annoyed her until we were presented with the repair and re-upholstery task.

    The lumbar carved section had broken away for two reasons; only an average quality PVA glue had been used for the repair and where the timber had fractured there was burl grain so it was originally flawed. We chipped away the remaining burl timber then stage by stage rebuilt the carved section in question using two-pack epoxy resin. Each section was masked-up and filled with resin then sanded into shape. After this was completed the re-built section was stained to match the remaining timber work.

    The existing upholstery was then completely removed with new jute webbing being fitted, coil springs then laced in and tied down and a hessian overlay fitted. A synthetic thumb roll was then fitted to the seat edges and filled in with high density premium padding then a bonded polyester overlay. The chair was then upholstered in a black cut pile cotton velvet and finished with twin piping. This method reduces the cost for our client but also creates a usable and durable seat however not authentic of the period.

    Our client was elated with the finished result especially because the chair would once again become a functional piece of furniture.

    Call us Today
  • Re-upholster Antique Chairs

    Occasionally we receive antique chairs which are basically well preserved but they have been previously shabbily re-upholstered or upholstered out of context with the era. This rarely does the furniture justice and usually results in complete restoration.

    Our client came to us with a lounge chair made in the 1890’s having been originally purchased by her deceased husband’s grandparents. She was honest in explaining that under her instructions the chair had been re-upholstered in the early 1980’s in a pastel cotton and the style modernised to match their décor at a previous residence. She was now ashamed of her previous decision and wanted the chair re-upholstered to its previous glory.

    The chair’s design had been modernised by having a loose seat cushion fitted and absence of piped detail. We removed all the upholstery stripping the chair down to the bare frame and the turned timber legs were then cleaned and polished. Heavy weight jute webbing was then fitted to the seat and back, the coil springs laced, tied down then hessian overlays fitted. We used synthetic ‘thumb roll’ on the seat front, arms and back scrolls then laminated premium polyurethane foams finished with polyester overlays. The seat cushion inner was fabricated from high resilience foam and encased with bonded polyester fibre.

    The chair was then upholstered using a fabric selected by our client which suited the chair and was basically in keeping with the period. The result was a chair which was modernised to a degree under the cover for comfort however retained much authenticity with the upholstery finish and piped detail. Our client was over joyed with her chair and no doubt will become a family heirloom.

    Call us Today
  • Refurbish Parker Knoll chairs

    Parker Knoll Chairs Perth Restored

    The Origination of Parker Knoll

    New seat and back heavy grade elastic webbing was fitted then high-density foam was laminated to the arms and frame bodies including the outside arm and back panels which were lined and padded. Polyester filled channelled and quilted back cushion inserts were fabricated. The premium foam polyester encased seat cushion inserts were fabricated by laminating two grades of foam creating a cushion that progressively firms and ensuring greater longevity.

    The new venture was quickly successful producing high quality sprung furniture for the mass market. During the war years the company produced wooden componentry for de Havilland and repaired gliders then reversed into furniture production after 1945. With increasing the company listed in 1950 and then in the 1960’s saw vast production of recliner chairs which became a signature item.

    The company went back to private ownership in 2004 after suffering financial difficulties then went through several ownerships and now has gone back to its roots producing high quality furniture from a state of the art factory in Nottinghamshire.

    How We Restored the Parker Knoll Chairs

    A set of two Parker Knoll chairs were completely stripped of the upholstery and sanded back to the bare timber.  Three coats of lacquer were applied being sanded between coats. The frames were then lightly rubbed back with super-fine steel wool to produce the required finish.

    The client selected a 1970’s period velvet for the upholstery. The padding was fabricated by laminating premium cushioning then encased in polyester fibre. The upholstery fabric suited these chairs embracing the era.

    Our Client’s Feedback

    Our client was overwhelmed with the chairs adding these pieces to her home filled with beautiful mid-century furniture.

    Call us Today to Have Your Furniture Reupholstered