Restoration of Antique Chairs

By Frank Parker

Genuine fine antique chairs become scarcer as time ticks on due to fatigue with function and unnecessary destruction. Poor and inappropriate furniture repairs due to operators not possessing the necessary skills also increase the scarcity. It is important to always use a reputable and skilled restorer.

Our client approached us with a dining chair from the 1880’s which was bequeathed to her by her maternal grandmother as one was for each granddaughter. After receiving the chair she had it repaired and re-upholstered however within a short time with only gentle use the lower back carved section again broke away. The chair remained in her lounge room as a decorative piece for several decades but constantly annoyed her until we were presented with the repair and re-upholstery task.

The lumbar carved section had broken away for two reasons; only an average quality PVA glue had been used for the repair and where the timber had fractured there was burl grain so it was originally flawed. We chipped away the remaining burl timber then stage by stage rebuilt the carved section in question using two-pack epoxy resin. Each section was masked-up and filled with resin then sanded into shape. After this was completed the re-built section was stained to match the remaining timber work.

The existing upholstery was then completely removed with new jute webbing being fitted, coil springs then laced in and tied down and a hessian overlay fitted. A synthetic thumb roll was then fitted to the seat edges and filled in with high density premium padding then a bonded polyester overlay. The chair was then upholstered in a black cut pile cotton velvet and finished with twin piping. This method reduces the cost for our client but also creates a usable and durable seat however not authentic of the period.

Our client was elated with the finished result especially because the chair would once again become a functional piece of furniture.

Call us Today

Similar Posts

  • Reupholster Art Deco Chairs

    ByFrank Parker

    From our understanding these chairs were made in Czechoslovakia in the late 1920’s, manufacturer unknown. For their time the construction techniques used are quite advanced utilising a ‘push-in seat’ and back flutes located with spring-edge wire. However the most significant thing about these chairs is the general proportion and balance of the design.

    A client contacted us saying that she had acquired two art deco European chairs requiring restoration. Upon initial inspection we found the chairs had been shabbily re-upholstered and covered in decades of grime. As we stripped away the fabric on these chairs it exposed some of the original upholstery providing enough information for an authentic reconstruction.

    The first step was several construction repairs to the timber frames then removing the layers of grime. The show-wood components of the frames were then gently sanded back, stained a mid-tone Oak then three coats of clear lacquer. Then with the upholstery we re-constructed the sprung edge seats and backs by lacing in the springs, fabricated the spring edge wire and tying down the springs. We then sewed on the hessian overlays and ring-clipped on polyurethane edge moulding. The seats and backs were then layered with premium foam and polyester overlays. The client’s fabric selection suited the chairs and was practical to upholster. The panels were cut being carefully pattern matched then largely pre-sewn but requiring some hand stitching.

    The re-furbishing of these chairs combined traditional methods with modern materials however did not compromise the design integrity. Our client was overjoyed with the result and the chairs now take pride of place in her lounge room.

    Call us Today

  • Le Cornu Furniture – reupholster

    ByFrank Parker

    Le Cornu was an iconic South Australian furniture manufacturing and retailing business. Operations commenced in 1861 when Phillip Le Cornu started a wholesale cabinet making business in Adelaide. In 1885 the factory was largely destroyed by fire and recommenced operations at a former church in North Adelaide. In 1921 the founder died and his son Phillip took over the business expanding operations and by 1924 employed 25 people.

    In 1954 the business went factory direct with a diversified range of furniture and over the next two decades expanded retail stores in S.A and Darwin. In 1989 the North Adelaide store was closed and then the business was sold to Fantastic Holdings in 2008.

    Our client approached us wanting to re-upholster a settee purchased by his parents from Le Cornu in 1959. This settee was the surviving piece of the lounge suite which he grew up with and lounged upon as a teenager. It was still upholstered in the original fabric being a ribbed velvet which would have been the latest trend at the time of purchase.

    We removed all the existing upholstery from the settee frame and it was well constructed with little structural work required. The frame was re-sprung with heavier gauge no-sag springs on the seat and the back springs were replaced with the same gauge. The springs were linked, outside arms and back were lined with hessian and high density body work padding applied. The original cushion inserts were latex and these were replaced with polyester encased premium cushions. The two seater settee was then upholstered to its original finish in a ribbed Zepel gold velvet.

    Our client was gobsmacked upon delivery of the settee saying it was just as he remembered it as a child growing up in Adelaide.

    Call us Today

  • Co-ordinating classic chairs

    ByFrank Parker

    Timberline Furniture commenced operations in Perth WA with the factory being located in Willetton. The furniture manufacturing business was founded by Ron Jones and Hedley Van Der Straaten in the early 70’s and ran through to the mid 90’s with about 10 – 12 staff. Ron was a Wood-Turner by trade and managed operations with Hedley managing sales and general business. Timberline predominantly manufactured dining furniture but also made some lounge and occasional furniture. During the 80’s they entered into a collaborative venture with co-ordinated designs, Trustyle Furniture making the lounge suites, George’s Cabinets making the cabinetry and Timberline the dining suites. These co-ordinated furniture ranges were sold by furniture retailers throughout W.A.     

    Our clients were involved in furniture retailing and furniture transport for many decades and contacted us to re-upholster their Timberline ‘Captain’s Chairs’. These were a very popular occasional chair from the late 70’s and early 80’s not just in residential sales but they were also used in commercial hospitality applications.

    The chairs were originally upholstered in a Nylex ‘Deerhide’ vinyl which was a quality product in its days so we advised using a vinyl from the Austex ‘Studio’ as a quality replacement. The existing upholstery was completely removed, then the show-wood frames cleaned and polished. New high density foam was laminated onto the padded areas and the chairs were upholstered to the original finish with piped and space studded detail.

    Our clients re-upholstered ‘Captain’s Chairs’ looked in place around their bar with complimentary comments passed over a few drinks.

    Call us Today

  • Problems with re-upholstering your old lounge suite

    ByFrank Parker

    Fixing up a previous reupholstery job

    This modular unit was manufactured by a local Perth, business ‘Farmer Furniture’ in the early 1980’s. It was re-upholstered 12 years ago however the clients had never been happy with the quality of the reupholstery job as it simply “did not feel like the old suite when new”.

    How we approached renewing this lounge suite

    We stripped the old upholstery from the modular frame. It revealed that the second layer of fabric had simply been placed over the initial fabric in which the suite was made. This style of reupholstery is very problematic. The issue is caused by the webbing, body padding and cushioning not being replaced resulting in this lounge furniture quickly returning to a dysfunctional state. Which is a waste of time and money for the owners.

    The next stage involved us:

    This process allowed us to modernise the upholstery finish without losing the authentic character of the lounge suite.

    The final result was a well finished and functional modular lounge this family will enjoy for many years into the future.

    Call us so we can help you reupholster your lounge suite

  • Tessa Vintage Furniture

    ByFrank Parker

    What is Tessa Furniture?

    Tessa Furniture is an iconic name in Australian furniture manufacturing being a prolific name during the heydays of the local furniture industry. We know re-furbished mid-century modernist furniture with a Scandinavian influence is a niche market. However the interest not only resides with those who have been fortunate to have witnessed this period of design history. Some discerning members of the younger generations are purchasing or inheriting or purchasing second hand Tessa furniture and having it restored.

    Why is Tessa Furniture So Popular?

    As per the above photographs Tessa lounges are extremely well designed and soundly constructed. This Tessa lounge suite was originally purchased in 1972. When the Tasmanian Blackwood timber was sanded and re-polished and new webbing and cushioning were re-upholstered – it looks amazing!

    Tessa Furniture History

    Tessa originally was known as Twen commencing operation in 1968. It then changed its name to Tessa in 1970. Tessa was formed by Fred Lowen, his brother Howard Lindsey and design technician Sigi Danielzik. Fred however commenced furniture manufacturing with Ernest Rodeck in the mid 1950’s having formed FLER which was sold in 1967. Tessa expanded operations during the 1970’s to become a national operation with international links.

    Call Us So We Can Help You Restore Your Special Furniture

  • Refurbish TV Chairs & Daynite sofa

    ByFrank Parker

    “TV chairs” and “Daynite sofas” became popular from the late 1950’s and remained in production through to the early 1970’s. This coincided with the introduction of television and the modern appliance age. Today we generally refer to TV chairs and Daynite sofas as mid-century furniture which has regained popularity amongst novices and enthusiasts of this era. This furniture setting was made in W.A. by Condor Furniture in Osborne Park owned by the Trethowan family.

    This set of TV chairs and Daynite sofa were presented to us by our client who wanted them completely refurbished to original condition. The existing upholstery was striped to the frames then the frames sanded back to raw timber. The timber frames were constructed from Nyatoh, a Malaysian timber which is ideal for this type of furniture. The frames were then stained brown teak and three coats of clear lacquer applied.

    The new upholstery started with replacing the no-sag springs then fabricating polyester encased premium cushion inserts. The upholstery fabric selected was similar to the original covering being a flat woven rust coloured fabric.

    The result was a refurbished classic mid-century lounge setting that took our clients back to the time of their initial purchase. We have no doubt that just as nostalgic memories will be relived good times are still to come for our clients to enjoy their furniture.

    Call us Today